Bookmark and Share

Law 6 (The bat)

1. The bat

The bat consists of two parts, a handle and a blade.

2. Measurements

All provisions in sections 3 to 6 below are subject to the measurements and restrictions stated in Appendix E.

3. The handle

(a) One end of the handle is inserted into a recess in the blade as a means of joining the handle and the blade. The part of the handle that is then wholly outside the blade is defined to be the upper portion of the handle. It is a straight shaft for holding the bat. The remainder of the handle is its lower portion used purely for joining the blade and the handle together. It is not part of the blade but, solely in interpreting 5 and 6 below, references to the blade shall be considered to extend also to the lower portion of the handle where relevant.

(b) The handle is to be made principally of cane and/or wood, glued where necessary and bound with twine along the upper portion.

(c) Providing 7 below is not contravened, the upper portion may be covered with materials solely to provide a surface suitable for gripping. Such covering is an addition and is not part of the bat. Note, however, 8 below.

(d) Notwithstanding 4(c) and 5 below, both the twine binding and the covering grip may extend beyond the junction of the upper and lower portions, to cover part of the shoulders as defined in Appendix E.

4. The blade

(a) The blade comprises the whole of the bat apart from the handle as defined above. The blade has a face, a back, a toe, sides and shoulders. See Appendix E.

(b) The blade shall consist solely of wood.

(c) No material may be placed on or inserted into either the blade or the lower portion of the handle other than as permitted in 3(d) above and 5 and 6 below, together with the minimal adhesives or adhesive tape used solely for fixing these items, or for fixing the handle to the blade.

5. Covering the blade

All bats may have commercial identifications on the blade. Type A and Type B bats may have no other covering on the blade except as permitted in 6 below. Type C bats may have a cloth covering on the blade. This may be treated as specified in 6 below.

Such covering is additional to the blade and is not part of the bat. Note, however, 8 below.

6. Protection and repair

Providing neither 4 above nor 7 below is contravened,

(a) solely for the purposes of either

(i) protection from surface damage to the face, sides and shoulders of the blade or

(ii) repair to the blade after damage material that is not rigid, either at the time of its application to the blade or subsequently, may be placed on these surfaces. Any such material shall not extend over any part of the back of the blade except in the case of (ii) above and then only when it is applied as a continuous wrapping covering the damaged area.

(b) solid material may be inserted into the blade for repair after damage other than surface damage. Additionally, for protection from damage, for Types B and C, material may be inserted at the toe and/or along the sides, parallel to the face of the blade.

The only material permitted for any insertion is wood with minimal essential adhesives.

(c) to prevent damage to the toe, material may be placed on that part of the blade but shall not extend over any part of the face, back or sides of the blade.

(d) the surface of the blade may be treated with non-solid materials to improve resistance to moisture penetration and/or mask natural blemishes in the appearance of the wood. Save for the purpose of giving a homogeneous appearance by masking natural blemishes, such treatment must not materially alter the colour of the blade.

Any materials referred to in (a), (b), (c) or (d) above are additional to the blade and not part of the bat. Note, however, 8 below.

7. Damage to the ball

(a) For any part of the bat, covered or uncovered, the hardness of the constituent materials and the surface texture thereof shall not be such that either or both could cause unacceptable damage to the ball.

(b) Any material placed on any part of the bat, for whatever purpose, shall similarly not be such that it could cause unacceptable damage to the ball.

(c) For the purposes of this Law, unacceptable damage is deterioration greater than normal wear and tear caused by the ball striking the uncovered wooden surface of the blade.

8. Contact with the ball

In these Laws,

(a) reference to the bat shall imply that the bat is held in the batsman’s hand or a glove worn on his hand, unless stated otherwise.

(b) contact between the ball and either (i) the bat itself

or (ii) the batsman’s hand holding the bat

or (iii) any part of a glove worn on the batsman’s hand holding the bat

or (iv) any additional materials permitted under 3, 5 or 6 above shall be regarded as the ball striking or touching the bat or being struck by the bat.

© Marylebone Cricket Club 2013

Share this page

Further Reading

Search Laws

Buy the laws of cricket now

Back to Top